Ablestik 导电银胶2030SC TDS

PRODUCT DESCRIPTION
ABLEBOND 2030SC provides the following product
characteristics:
Technology Proprietary Hybrid Chemistry
Appearance Silver
Cure Heat cure
pH 4.5
Product Benefits • Snap curable
• Low stress
Application Die attach
Filler Type Silver
Key Substrates Most metals
ABLEBOND 2030SC die attach adhesive has been formulated
for use in high throughput die attach applications. This material
is designed to minimize stress and resulting warpage between
dissimilar surfaces. It can be used in a variety of package sizes
.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Thixotropic Index (0.5/5 rpm) 4.6
Viscosity, Brookfield CP51, 25 °C, mPa·s (cP):
Speed 5 rpm 11,600
Work Life @ 25°C, hours 24
Shelf Life @ -40°C (from date of manufacture), year 1
TYPICAL CURING PERFORMANCE
Cure Schedule
90 seconds @ 110°C
Alternative Cure Schedule
10 seconds @ 150°C
Weight Loss on Cure
10 x 10 mm Si die on glass slide, % 0.4
The above cure profiles are guideline recommendations. Cure
conditions (time and temperature) may vary based on customers'
experience and their application requirements, as well as customer
curing equipment, oven loading and actual oven temperatures.
TYPICAL PROPERTIES OF CURED MATERIAL
Physical Properties:
Thermal Conductivity, W/mK 2.3

Tensile Modulus, DMTA :
@ -65 °C N/mm² 6,200
(psi) (900,000)
@ 25 °C N/mm² 3,300
(psi) (480,000)
@ 150 °C N/mm² 350
(psi) (50,000)
@ 250 °C N/mm² 450
(psi) (65,000)
Extractable Ionic Content, @ 100°C ppm:
Chloride (Cl-) <20
Sodium (Na+) <30
Potassium (K+) <5
Weight Loss After Cure, %:
16 hours Isothermal @ 125ºC 0.41
Ramp to 230ºC 0.5
Electrical Properties:
Volume Resistivity, ohms-cm:
cured 90 seconds @ 110ºC 0.0002
Bond Joint Resistance, ohms:
cured 90 seconds @ 110ºC, Cu/Cu, 25μm Bondline 0.008
TYPICAL PERFORMANCE OF CURED MATERIAL
Die Shear Strength vs Substrate:
2 X 2 mm die, kg-f,
Die on Substrate: @ RT
Si die on Pd 1.90
Au die on SS 2.24
Au die on Au 2.11
Die Shear Strength vs Die Shear Temperature:
3 X 3 mm Si die, kg-f,
cured 90 seconds @ 110ºC
Substrate @25°C @150°C @200°C
PBGA-FR4 1.90 0.96 0.87
GENERAL INFORMATION
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
THAWING:
1. Allow container to reach room temperature before use.
2. After removing from the freezer, set the syringes to stand
vertically while thawing.
3. Refer to the Syringe Thaw time chart for the thaw time
recommendation.
4. DO NOT open the container before contents reach 25°C
temperature. Any moisture that collects on the thawed
container should be removed prior to opening the
container.

5. DO NOT re-freeze. Once thawed to -40°C, the adhesive
should not be re-frozen.
Temperature, °C
Syringe Thaw Time, Minutes
30
20
10
0
-10
-20
-30
-40
0 10 20 30 40 50
1cc
3cc 10cc 30cc
DIRECTIONS FOR USE
1. Thawed adhesive should be immediately placed on
dispense equipment for use.
2. If the adhesive is transferred to a final dispensing
reservoir, care must be exercised to avoid entrapment of
contaminants and/or air into the adhesive.
3. Adhesive must be completely used within the products
recommended work life of 24 hours.
4. Silver-resin separation may occur if the adhesive is left
out at 25°C beyond the recommended work life.
Not for product specifications
The technical data contained herein are intended as reference
only. Please contact your local quality department for
assistance and recommendations on specifications for this
product.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: -40 °C. Storage below minus (-)40 °C or
greater than minus (-)40 °C can adversely affect product
properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP

Note
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Henkel
Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental
damages of any kind, including lost profits. The discussion
herein of various processes or compositions is not to be
interpreted as representation that they are free from
domination of patents owned by others or as a license under
any Henkel Corporation patents that may cover such
processes or compositions. We recommend that each
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered
by one or more United States or foreign patents or patent
applications.

下载附件查看PDF文件：
  ABLEBOND 2030SC-EN (65.4 KB, 13 次)
您没有权限下载此文件。