PRODUCT DESCRIPTION

EO1016 provides the following product characteristics:

EO1016 is  an  epoxy  encapsulant  intended  for  applications requiring  excellent  handling  properties.  The  cured  material survives severe thermal shock and offers continuous service to 177 °C. It is particularly suited for use on transistors and similar semiconductors, can be used for encapsulation of watch ICs.

TYPICAL PROPERTIES OF UNCURED MATERIAL

Viscosity, Brookfield – RVF, 25 °C, mPa·s (cP):
Spindle 6, speed 2                                                     62,000
Spindle 6, speed 20                                                   58,000
Thixotropic Index                                                        1.1
Specific Gravity @ 25ºC                                              1.56
Shelf Life:
@ 4ºC, months                                                          12
@ -40ºC, months                                                       12
Gel Time @ 121ºC, minutes                                        4.5
Pot life @ 25 °C, months                                             3
Flash Point – See MSDS

TYPICAL CURING PERFORMANCE Recommended Cure Schedule
20 minutes @ 150°C

Alternative Cure Schedule
24 hours @ 93°C

The above cure profile is a guideline recommendation. Cure conditions (time and temperature) may vary based on customers’ experience and their application requirements, as well as customer curing equipment, oven loading and actual oven temperatures.

Differential Scanning Calorimetry

TYPICAL PROPERTIES OF CURED MATERIAL

Physical Properties:
Coefficient of Linear Thermal Expansion, ppm/ºC:
Below Tg                                                                    46
Above Tg                                                                    140
Glass Transition Temperature, °C                             126
Coefficient of Thermal Conductivity, W/(m·K)         0.39
Extractable Ionic Content, , ppm:
Chloride (Cl-)                                                            1.2
Tensile Strength                                             N/mm²    55.17 (psi)  (8,000)
Flexural Modulus                                            N/mm²    5,880 (psi)  (852,600)
Flexural strength                                            N/mm²    100 (psi)     (14,500)
Adhesion psi                                                                         3600
Cohesive
Al-Al Tensile shear
Elongation, %                                                             1.8
Shore Hardness , Durometer D                                 ≥86
Linear Shrinkage, 10 grams, %                                1.7
Moisture Absorption, %:
24 hours immersion @ 25°C                                    0.06
24 hours immersion @ 50°C                                    0.23

Electrical Properties:
Dielectric Constant / Dissipation Factor, IEC 60250:@ 25 °C:
1kHz                                                                    4.3 / 0.0084
Arc Resistance, ASTM D495,                                     180
Volume Resistivity, IEC 60093,                                  6×1015
Surface Resistivity, IEC 60093,                                  1×1016

GENERAL INFORMATION
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).

Not for product specifications

The technical data contained herein are intended as reference only. Please contact your local quality department for assistance and recommendations on specifications for this product.

Directions for use
1.  Mix thoroughly each time it is used.
2.  Heating  to  32 to  43°C   will  lower  viscosity  and  aid  in mixing and pouring.

Storage
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.Liquid  Storage  –  Liquids  should  be  stored  at  23°C  or below,  in  closed  containers.  If  stored  below  23°C,  the material MUST be allowed to come to room temperature, in the sealed container, to avoid moisture contamination. Material removed from containers may be contaminated during use.  Do not return product to the original container.  Henkel Corporation cannot assume responsibility for product  which has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please   contact   your   local   Technical   Service   Center   or Customer Service Representative.

Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm²  x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP

Note

The data contained herein are furnished for information only and are believed to be reliable.  We cannot assume responsibility for the results obtained by others over whose methods we have no control.  It is the user’s responsibility to determine suitability for the user’s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporation’s products.  Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted  as  representation  that  they  are  free  from domination of patents owned by others or as a license under any   Henkel   Corporation   patents   that   may   cover   such processes or compositions.  We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide.  This product may be covered by one or more United States or foreign patents or patent applications.

华为网盘下载：http://dl.dbank.com/c019oni7uy

注册本地下载：

  EO1016 TDS&MSDS (94.6 KB, 4 次)
您没有权限下载此文件。