Araldite® 2011 (AW 106/HV 953U)

Two component epoxy paste adhesive

Key properties            ·     High shear and peel strength

•  Tough and resilient
•  Good resistance to dynamic loading
•  Bonds a wide variety of materials in common use

Description                 Araldite 2011 is a multipurpose, two component, room temperature curing, paste adhesive of high strength and toughness.It is suitable for bonding a wide variety of metals, ceramics, glass, rubber, rigid plastics and most other materials in common use. It is a versatile adhesive for the craftsman as well as most industrial applications.

Product data

Processing                 Pretreatment

The strength and durability of a bonded joint are dependant on proper treatment of the surfaces to be bonded. At the very least, joint surfaces should be cleaned with a good degreasing agent such as acetone, iso-propanol (for plastics) or other proprietary degreasing agents in order to remove all traces of oil, grease and dirt.Low grade alcohol, gasoline (petrol) or paint thinners should never be used.The strongest and most durable joints are obtained by either mechanically abrading or chemically etching (“pickling”) the degreased surfaces. Abrading should be followed by a second degreasing treatment

Resin and hardener should be blended until they form a homogeneous mix. Resin and hardener are also available in cartridges incorporating mixers and can be applied as ready-to-use adhesive with the aid of the tool recommended by Huntsman Advanced Materials.

Application of adhesive

The resin/hardener mix is applied with a spatula, to the pretreated and dry joint surfaces.A layer of adhesive 0.05 to 0.10 mm thick will normally impart the greatest lap shear strength to the joint.The joint components should be assembled and clamped as soon as the adhesive has been applied. An even contact pressure throughout the joint area will ensure optimum cure.

Typical cured properties

Unless otherwise stated, the figures given below were all determined by testing standard specimens made by lap-jointing 170 x 25 x 1.5 mm strips of aluminium alloy. The joint area was 12.5 x 25 mm in each case. The figures were determined with typical production batches using standard testing methods. They are provided solely as technical information and do not constitute a product specification.

……

下载附件查看全文：

华为网盘下载：http://dl.dbank.com/c0rje2l2r4

注册本地下载：

  Araldite 2011-TDS&MSDS (84.1 KB, 8 次)
您没有权限下载此文件。

近日了解到亨斯迈旗下有一款爱牢达AV119产品，主要是单组分热固化环氧胶粘剂，产品TDS我大概看了一下，应该与目前的红胶体系有些类似，但是有两个比较特殊的地方，一个是粘接强度非常大，另外一个是具有一定的韧性，可以承受高频的震荡冲击。据了解市面的价格好像是五六百块一公斤，而且这个产品也是按公斤来销售的，估计用量也不小。有空让公司研发部门分析一下此款产品，顺便也去了解一下此类产品的应用点。闲话少说，先贴上TDS资料，需要看原版的请下载附件查看！：

ARALDITE® AV 119
EPOXY ADHESIVE PASTE
DESCRIPTION: Araldite AV 119 epoxy adhesive is a one-component, multi-purpose paste that
is thixotropic and is designed for heat curing at temperatures from 248°F to
356°F (120°C to 180°C). The adhesive will fill gaps to 0.12 in. (3mm). The
tough, high-strength adhesive is well suited for metal bonding and joining
materials including ceramics, glass, rubber and temperature-resistant plastics.
APPLICATIONS: Metal- to-metal bonding.
ADVANTAGES: • Good heat resistance to 248°F (120°C)
• Good peel strength
• Good chemical resistance
TYPICAL Test Values(1)
PROPERTIES: Property Test Method One Component Epoxy
Color Visual Beige
Specific Gravity ASTM D-792 1.15 - 1.20
Viscosity at 77°F (25°C), cP Thixotropic paste
PROCESSING Pretreatment
The strength and durability of a bonded joint are dependant on proper treatment
of the surfaces to be bonded. At a minimum, joint surfaces should be cleaned
with a good degreasing agent such as acetone or other proprietary degreasing
agents in order to remove all traces of oil, grease and dirt.
Low grade alcohol, gasoline or paint thinners should never be used.
The strongest and most durable joints are obtained by either mechanically
abrading or chemically etching (“pickling”) the degreased surfaces. Abrading
should be followed by a second degreasing treatment
Adhesive Application
The resin/hardener mix is applied with a spatula, to the pretreated and dry joint
surfaces.
A layer of adhesive 0.002 to 0.004 in. (0.05 to 0.10mm thick) will normally impart
the greatest lap shear strength to the joint.
The joint components should be assembled and clamped as soon as the
adhesive has been applied. An even contact pressure throughout the joint area
will ensure optimum cure.
Mechanical processing
Specialist firms have developed metering, mixing and spreading equipment that
enables the bulk processing of adhesive.
Huntsman Advanced Materials will be pleased to advise customers on the choice
of equipment for their particular needs.
Equipment maintenance
All tools should be cleaned with hot water and soap before adhesives residues
have had time to cure. The removal of cured residues is a difficult and timeconsuming
operation.
If solvents such as acetone are used for cleaning, operators should take the
appropriate safety precautions and, in addition, avoid skin and eye contact.
Curing times
Temperature ° F (°C) 248 (120) 284 (140) 302 (150) 320 (160) 356 (180)
Cure time minutes 60 45 30 20 10
Lap shear
strength at
74°F (23°C)
psi
(N/mm2)
2900 –
3,335
(20-23)
3,625 –
4,060
(25-28)
3,915 –
4,350
(27-30)
4,205 –
4,640
(29-32)
4,350 –
4,785
(30-33)
Note: Temperatures below 248°F (120°C) will not give adequate cure even when
cure time is prolonged.
Cure temperatures above 302°F (150°C) should be avoided when joining
materials with different coefficients of linear thermal expansion because stresses
will be set up in the bond line upon cooling. This effect is particularly marked
where the bond surfaces are large.
Typical cured
properties
Unless otherwise stated, the figures given below were determined by testing
standard specimens made by lap-jointing 6.6 x 1.0 x 0.06 in.(170 x 25 x 1.5mm)
strips of aluminum alloy. The joint area was 0.5 x 1.0 in. (12.5 x 25mm) in each
case.
The figures were determined with typical production batches using standard
testing methods. They are provided solely as technical information and do not
constitute a product specification.
Average lap shear strengths of typical metal-to-metal joints (ISO 4587)
Cured for 30 mins at 302°F (150°C) and tested at 74°F (23°C)
Pretreatment - Sand blasting
0 725 1,450 2,175 2,900 3,625 4,350 5,075
Aluminum
Steel 37/11
Stainless steel V4A
Galvanized steel
Copper
Brass
psi**
*
*
*
*Failure stress close to elastic limit yield stress of the metal.
** 725 psi = 5 N/mm2; 1,450psi = 10 N/mm2; 2,175 psi = 15 N/mm2; 2,900 psi = 20 N/mm2;
3,625 psi = 25 N/mm2; 4,350 psi = 30 N/mm2; 5,075 psi = 35 N/mm2
Lap shear strength versus temperature (ISO 4587) (typical average values)
Cure:45 mins at 302°F (150°C)
0
1,450
2,900
4,350
5,800
-76 -40 -4 32 68 104 140 176 212 248
°F*
psi**
*-76°F = -60°C; -40°F = -40°C; -4°F = -20°C; 32°F = 0°C; 68°F = 20°C; 104°F = 40°C;
140°F = 60°C; 176°F = 80°C; 212°F = 100°C; 248°F = 100°C
**1,450psi = 10 N/mm2; 2,900 psi = 20 N/mm2; 4,350 psi = 30 N/mm2; 5,800 psi = 40 N/mm2
Roller peel test (ISO 4578)
Cured 30 mins at 150°C, pli (N/mm) 45.7 - 57.1 (8 - 10)
Coefficient of thermal expansion (VDE 304),
at 68°F-140°F (20°C-60°C) in./in./ºC 57x10-6
at 68°F-212°F (20°C-100°C) in./in./°C 68x10-6
Electrolytic corrosion (DIN 53489) Grade A 1
Electrical Properties
Thermal Conductivity, W/mK 0.26
Surface Resistivity, ohms 3.5 E+13
Dielectric Strength, volt/mil 450
Volume Resistivity, ohms-cm 6.2 E+16
Dielectric Constant, at 50Hz/1KHz/10KHz 4.0/4.0/3.8
Loss Tangent, % at 50Hz/1KHz/10KHz 1.0/1.1/1.5
Lap shear strength after 90 days immersion in various media
at 74°F (23°C), Typical average values.
0 725 1450 2175 2900 3625 4350
As-made value
Methanol
Gasoline
Ethyl acetate
Acetic acid, 10%
Acetone
Trichloroethylene
Water at 74°F (23°C)
Water at 194°F (90°C)
psi*
Cure: 30 mins at 302°F (150°C)
* 725 psi = 5 N/mm2; 1,450psi = 10 N/mm2; 2,175 psi = 15 N/mm2; 2,900 psi = 20 N/mm2;
3,625 psi = 25 N/mm2; 4,350 psi = 30 N/mm2;
Lap shear strength versus tropical weathering (40/92, DIN 50015; typical average values)
Cured: 30 min at 302°F (150°C); Tested at 74°F (23°C)
0 725 1450 2175 2900 3625 4350
As made value
After 30 days
After 60 days
After 90 days
psi*
* 725 psi = 5 N/mm2; 1,450psi = 10 N/mm2; 2,175 psi = 15 N/mm2; 2,900 psi = 20 N/mm2;
3,625 psi = 25 N/mm2; 4,350 psi = 30 N/mm2;
Shear modulus (DIN 53445)
Cure:30 min/302°F (150°C), Ksi (GPa)
77°F (25°C)
122°F (50°C)
167°F (75°C)
212°F (100°C)
257°F (125°C)
302°F (150°C)
203 (1.4)
188 (1.3)
160 (1.1)
102 (0.7)
44 (0.3)
2,175 psi (15 MPa)
CAUTION:
Huntsman Advanced Materials Americas Inc. maintains up–to-date Material Safety Data Sheets (MSDS)
on all of its products. These sheets contain pertinent information that you may need to protect your
employees and customers against any known health or safety hazards associated with our products.
Users should review the latest MSDS to determine possible health hazards and appropriate precautions
to implement prior to using this material. Copies of the latest MSDS may be requested by calling our
customer service group at 800-367-8793 or emailing your request to adhesives_group@huntsman.com.
FIRST AID!
Eyes and skin: Flush eyes with water for 15 minutes. Contact a physician if irritation persists. Wash skin
thoroughly with soap and water. Remove and wash contaminated clothing before reuse.
Inhalation: Remove subject to fresh air.
Swallowing: Dilute by giving water to drink and contact a physician promptly. Never give anything to drink
to an unconscious person.
KEEP OUT OF REACH OF CHILDREN
FOR PROFESSIONAL AND INDUSTRIAL USE ONLY
IMPORTANT LEGAL NOTICE:
Sales of a referenced product (“Product”) are subject to the general terms and conditions of sale of Huntsman Advanced Materials Americas
Inc. (“Huntsman”).
WARRANTY: Huntsman warrants to the Buyer that the Product will conform to the published specifications for that Product at the time of
manufacture, and that the Product will be free from defects in material and workmanship in normal use.
DISCLAIMER AND LIMITATION OF LIABILITY: EXCEPT AS SET FORTH ABOVE, SELLER MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Huntsman cannot
control Buyer’s application and use of the Product and accepts no responsibility therefore. No statement or recommendation contained in any
Product literature may be construed as a representation about the suitability of a Product for the particular application of Buyer or user or as an
inducement to infringe any relevant patent. Buyer is responsible to ensure that its intended use of the Product does not infringe any thirdparty’s
intellectual property rights. Seller neither assumes, nor authorizes any representative or other person to assume for it, any obligation or
liability other than as is expressly set forth herein. UNDER NO CIRCUMSTANCES SHALL HUNTSMAN BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR OTHER INDIRECT DAMAGES AS A RESULT OF A BREACH OF ANY WARRANTY OR THE FAILURE OF A
PRODUCT OR ANY CLAIM THAT IS ESSENTIALLY BASED UPON SUCH BREACH OR FAILURE. Any claim by Buyer, whether arising in
contract, tort, negligence, breach of warranty, strict liability, or otherwise, related to a Product shall be limited to, and the sole liability of Seller
and the sole remedy of Buyer for any claims shall be for, the purchase price of the Product in respect of which such claim is made. The
foregoing DISCLAIMER and LIMITATION OF LIABILITY supercedes Buyer’s documents.
WARNING: Technical data and results are based upon tests under controlled laboratory conditions and must be confirmed by Buyer by testing
for its intended conditions of use. The Product has not been tested for, and therefore is not recommended or suitable for, uses for which
prolonged contact with mucous membranes, abraded skin, or blood is intended or likely, or for uses for which implantation within the human
body is intended, and Huntsman assumes no liability for any such uses.
© 2004 Huntsman Advanced Materials Americas Inc.
Araldite is a registered trademark of Huntsman LLC or
an affiliate thereof in one or more, but not all, countries.

点击下载附件查看TDS资料：
  TDS-A119(US).pdf (159.6 KB, 9 次)
您没有权限下载此文件。