PRODUCT DESCRIPTION

ABLEBOND 8387B   provides   the   following  product characteristics:

Technology	Epoxy
Appearance	Black
Cure	Heat cure
Product Benefits	• Non-conductive • Fast cure • Black  pigmentation  for  blocking  stray light
Application	Die attach
Typical Package Application	Optoelectronic devices

ABLEBOND 8387B  nonconductive  die  attach  adhesive  has been formulated for use in high throughput die attach applications. This adhesive can be fast cured using directed heat energy or hot plate curing techniques. In conventional box or convection conveyor oven curing, it will cure at temperatures as low as 100ºC.

TYPICAL PROPERTIES OF UNCURED MATERIAL
Thixotropic Index (0.5/5 rpm) ≥4.5
Viscosity, Brookfield CP51, 25 °C, mPa·s (cP):  Speed 5 rpm 9,500
Work Life @ 25°C, hours 48
Shelf Life @ -40°C (from date of manufacture), year 1

TYPICAL CURING PERFORMANCE
Cure Schedule   2 minutes @ 150°C
Alternative Cure Schedule   30 minutes @ 100°C
The above cure profiles are guideline recommendations. Cure conditions (time and temperature) may vary based on customers’ experience and their application requirements, as well as customer curing equipment, oven loading and actual oven temperatures.

TYPICAL PROPERTIES OF CURED MATERIAL
Physical Properties:
Coefficient of Thermal Expansion :   Below Tg, ppm/°C 94
Above Tg, ppm/°C 165
Glass Transition Temperature (Tg) by TMA, °C      96

Tensile Modulus, DMTA :
@ -65 °C     N/mm²     2,840    (psi) (411,000)
@ 25 °C      N/mm²     1,400    (psi) (203,000)
@ 100 °C   N/mm²     580       (psi) (84,000)
@ 150 °C N/mm²       77          (psi) (11,000)
@ 200 °C N/mm²      59          (psi) (8,500)
@ 250 °C N/mm²      53          (psi) (7,700)
Extractable Ionic Content, @ 100°C ppm:    Chloride (Cl-) <300
Sodium (Na+) <10
Potassium (K+) <5
Water Extract Conductivity, μmhos/cm         190

TYPICAL PERFORMANCE OF CURED MATERIAL
Die Shear Strength:
2 X 2 mm Si die, MPa (psi),

Substrate	@25°C
T2 FR-2 Leadframe	27 (3900)

3 X 3 mm Si die, MPa (psi),

Substrate	@25°C
Ag/Cu leadframe	28.1 (4100)
Cu leadframe	30.5 (4400)

12.7 X 12.7 mm Si die, MPa (psi),

Substrate	@250°C
Cu leadframe	1.9 (270)

Chip Warpage vs Chip Size:
0.38 mm thick Si die on Cu leadframe @25°C, μm

Chip Size:	Warpage:
12.7 x 12.7mm	35

GENERAL INFORMATION

For safe handling information on this product, consult the

Material Safety Data Sheet, (MSDS).

THAWING:

1.  Allow container to reach room temperature before use.

2.  After removing from the freezer, set the syringes to stand vertically while thawing.

3.  DO NOT open the container before contents reach 25°C temperature. Any moisture that collects on the thawed container should be removed prior to opening the container.

4.  DO NOT re-freeze. Once thawed to -40°C, the adhesive should not be re-frozen.

 

DIRECTIONS FOR USE

1. Thawed adhesive should be immediately placed on dispense equipment for use.

2.  If  the  adhesive  is  transferred  to  a  final  dispensing reservoir, care must be exercised to avoid entrapment of contaminants and/or air into the adhesive.

3. Adhesive must be completely used within the products recommended work life of 48 hours.

 

Not for product specifications

The technical data contained herein are intended as reference only. Please contact your local quality department for assistance and recommendations on specifications for this product.

 

Storage

Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.

Optimal Storage:  -40 °C.  Storage below minus (-)40 °C or greater than minus (-)40 °C can adversely affect product properties.

Material removed from containers may be contaminated during use.  Do not return product to the original container.  Henkel Corporation cannot assume responsibility for product  which has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please   contact   your   local   Technical   Service   Center   or Customer Service Representative.

 

Conversions

(°C x 1.8) + 32 = °F kV/mm x 25.4 = V/mil mm / 25.4 = inches

N x 0.225 = lb N/mm x 5.71 = lb/in N/mm²  x 145 = psi MPa x 145 = psi N·m x 8.851 = lb·in N·m x 0.738 = lb·ft

N·mm x 0.142 = oz·in mPa·s = cP

Note

The data contained herein are furnished for information only and are believed to be reliable.  We cannot assume responsibility for the results obtained by others over whose methods we have no control.  It is the user’s responsibility to determine suitability for the user’s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporation’s products.  Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted  as  representation  that  they  are  free  from domination of patents owned by others or as a license under any   Henkel   Corporation   patents   that   may   cover   such processes or compositions.  We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide.  This product may be covered by one or more United States or foreign patents or patent applications.

据说是使用30G针头点胶不堵针头，而且可以80度固化的胶水。但是查到了四个型号，不知道哪个是这个应用点。堵针头可是很多胶水都可能需要面对的问题。 （国内的两家公司据说也快开发出类似的胶水，关注验证中）

华为网盘下载：http://dl.dbank.com/c09st5n5dt

注册本地下载：

  ablebond 8387B (248.6 KB, 8 次)
您没有权限下载此文件。